Product ID:HM-8221, THERMOPLASTIC ADHESIVE
MSDS Date:07/18/1986
FSC:8040
NIIN:00N032437
MSDS Number: BNSRG

Emergency Phone: 612-481-3300

Info Phone: 612-481-3300

Preparer: JOHN R. DOLMAR

Cage: R1331

Telephone: 612-236-5300/ -5309 FAX

Cage: 0DH19

PETROLEUM WAX (FUME)

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: EYES: VAPORS AND FUMES MAY
CAUSE IRRITATION. SKIN: NO KNOWN EFFECTS. INHALATION: VAPORS AND
FUMES MAY CAUSE IRRITATION OF NOSE, THROAT AND RESPIRATORY TRACT.
CHRONIC: NO ANTICIPATED CHRONIC EFF ECTS. CONTACT WITH MOLTEN
MATERIAL WILLCAUSE BURNS.
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:SKIN: IMMERSE CONT AREA IN COLD, CLEAN WATER IMMEDIATELY. DO
NOT ATTEMPT TO REMOVE SET PRODUCT. COVER CONTACT AREA WITH CLEAN
WET COMPRESSES AND TAKE SUBJECT TO PHYSICIAN IMMEDIATELY.
INHALATION: REMO VE SUBJECT TO FRESH AIR. CALL PHYSICIANIF SYMPTOMS
PERSIST. INGESTION: CALL MD IMMEDIATELY . EYES: FLUSH WITH WATER
FOR AT LEAST 15 MINUTES .

Flash Point Method:TCC
Flash Point:>400F,>204C
Extinguishing Media:CARBON DIOXIDE, DRY CHEMICAL, CHEMICAL FOAM.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT . AVOID USING WATER ON MOLTEN MATERIAL TO
REDUCE SPLATTERING AND SPREADING OF FIRES.
Unusual Fire/Explosion Hazard:NONE KNOWN.

Spill Release Procedures:ALLOW TO SOLIDIFY AT ROOM TEMPERATURE, SCRAPE
UP AND PLACE IN DISPOSAL CONTAINER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:NO SPECIAL REQUIREMENTS FOR STORAGE.
Other Precautions:AVOID BREATHING VAPORS/FUMES. USE ONLY WITH ADEQUATE
VENTILATION. AVOID CONTACT WITH MOLTEN PRODUCT.

Respiratory Protection:NOT NORMALLY REQUIRED. WEAR NIOSH/MSHA APPROVED
RESPIRATOR APPROPRIATE FOR EXPOSURE OF CONCERN .
Ventilation:AT APPLICATION TEMPERATURE LOCAL EXHAUST SHOULD BE PROVIDED
OVER PREMELTING RESERVOIR.
Protective Gloves:THERMALLY PROTECTIVE GLOVES.
Eye Protection:CHEM WORK GOG/FULL LGTH FACESHLD .
Other Protective Equipment:LONG SLEEVED SHIRT. PROVIDE COLD WATER
SOURCE FOR BURN TREATMENT. HAVE EYE WASHES AVAILABLE WHERE EYE
CONTACT CAN OCCUR.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.

HCC:N1
Spec Gravity:1.01
Appearance and Odor:SOLID

Stability Indicator/Materials to Avoid:YES
NONE SPECIFIED BY MANUFACTURER.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:INCOMPLETE COMBUSTION CAN YIELD: LOW
MOLECULAR WEIGHT HYDROCARBONS, CARBON MONOXIDE.

Waste Disposal Methods:PROD DOES NOT MEET DEFINITION OF HAZ WASTE UNDER
U.S. EPA HAZARDOUS WASTE REGS, 40 CFR 261. DISP OF IN AN APPRVD
INDUS LANDFILL; CONSULT YOUR STATE/LOCAL AUTH FOR PROPER DISP IN
EVENT MORE RESTRICTIVE REQS APPLY. DISP I/A/W FED, ST & LOC REGS .

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.